Steel Shot and Grit Sizes: How to Specify a Grade
Read S and G size designations correctly, separate particle-size acceptance from hardness and material requirements, and write an inspectable steel-abrasive purchase specification.
Review the information on this page and confirm product selection against the operating context.
A steel-abrasive size code identifies a grading class, not the diameter of every particle or the profile the abrasive will leave on a workpiece. To place an inspectable order, pair the code with the material, governing size criteria, hardness requirement and agreed sampling and test methods.
What do S and G size numbers actually mean?
SAE J444_202306 defines cast-shot and grit size numbers used for cleaning and peening. An S number is based on the opening of a nominal test sieve, expressed in ten-thousandths of an inch. For example, S330 corresponds to 0.0330 in, approximately 0.84 mm, at that nominal sieve. It does not say that each S330 particle is 0.84 mm across. A G number follows the designation of its nominal test sieve with a G prefix; it should not be read as a direct decimal particle diameter.
The size designation is only the entry point to a grading requirement. The applicable sieve distribution determines how much material may pass or be retained at specified sieve openings. A single “nominal size” in millimetres cannot replace that distribution.
YUXIN's high carbon cast steel shot catalogue lists S330 and also uses an internal SS-1.0 class description. These labels serve different purposes: the internal class description is not a substitute for the SAE nominal test-sieve definition or for the acceptance table. The low carbon cast steel shot catalogue also lists S330; the shared size code does not make the two materials interchangeable. The cast steel grit catalogue lists, for example, GP25, combining a GP hardness class with a grit-size designation. Confirm the size distribution and hardness requirement for the exact ordered product.
Separate four different specifications
Question in the purchase order | What answers it | What it does not prove |
|---|---|---|
Which type and grade are supplied? | Product name, material type, S or G size designation and, for grit, the agreed hardness class | Particle-size distribution or batch conformity by itself |
What particle sizes may be present? | Governing sieve-distribution limits and a test method | A guaranteed workpiece surface profile |
What material properties are required? | Applicable product specification, hardness range and any chemistry or structural limits | That a different material with the same S number is equivalent |
What surface must blasting produce? | The job's cleanliness and profile criteria, measured on the workpiece | Conformity of the abrasive lot as supplied |
This distinction prevents a common purchasing error: specifying only “S330 steel shot” leaves open whether the material is high- or low-carbon, which distribution applies, how it will be tested and whether the process result is acceptable. It also prevents a surface-profile target from being confused with an abrasive sieve opening.
Read a sieve table without changing its meaning
A usable size table identifies the product grade, each sieve opening and unit, the quantity passing or retained, and whether a percentage is a minimum, maximum or range. “Mesh” by itself is not an opening in millimetres; read the stated opening and the governing test-sieve specification. Check whether the percentages are cumulative or individual fractions before comparing two suppliers' tables.
Consider YUXIN's high-carbon shot page. Its technical information maps S330 to the internal SS-1.0 class and presents a separate particle-size distribution table under internal class labels. For an S330 request, find the SS-1.0 column. The current table does not state whether its percentages mean material passing or retained on each sieve, so those cells cannot be turned into purchase-acceptance limits without the table's technical definition. The “1.0 mm class” label is not itself an acceptance limit, and a blank cell does not mean zero or impose an additional limit unless the table legend says so.
Sampling also matters. ISO 11125-1:2018 addresses sampling a consignment and preparing test portions; ISO 11125-2:2018 gives a sieving method for determining the particle-size distribution of metallic blast-cleaning abrasives. A sieve result is meaningful only with its sample, method and applicable acceptance limits.
Know which standard answers which question
Reference | Main role in this decision |
|---|---|
Cast-shot and grit size-number system for cleaning and peening | |
Requirements for newly supplied high-carbon cast-steel shot and grit | |
Requirements for newly supplied low-carbon cast-steel shot | |
Sampling and determination of particle-size distribution; Part 2 has its own method record | |
Vickers hardness test method for metallic abrasive particles; the method is not recommended below 0.3 mm |
The ISO 11124 product standards apply to abrasive in its new condition, not to the changing operating mix in a recovery system. The ISO 11125 methods explain how a characteristic is tested; they are not a substitute for agreeing on its acceptance limit. A hardness value reported in HRC on a product page must not be described as an ISO 11125-3 Vickers test result without the corresponding test record.
Standards and editions also differ by purchase contract. State the edition actually required by the order; do not silently replace an agreed earlier edition. If both SAE and ISO documents are cited, specify which document governs each property and how any conflicting limits will be resolved.
A worked purchase example: S330 is not enough
An initial request might say “S330 steel shot for blast cleaning.” A technical purchaser can make it actionable by resolving these items:
Material: high-carbon or low-carbon cast-steel shot. Both are listed by YUXIN in S330, but their product specifications differ.
Size: S330 under the agreed size standard and edition, with the full sieve-distribution limits rather than only a nominal diameter.
Other properties: hardness range and any chemistry, density or structure requirements from the applicable material specification.
Evidence: lot identification, the sampling and test methods to be used, and the inspection results the buyer requires.
Commercial details: quantity, packaging, destination and the model's quoted supply terms.
An example inquiry could read: “High-carbon cast-steel shot, S330; size criteria under SAE J444_202306. Please identify the applicable sieve-distribution limits, agreed hardness requirement and lot-identified size-test results, and quote the required quantity and packaging.” This specifies what the buyer needs to inspect without claiming that a particular batch has already passed a test.
This is a specification sequence, not a claim that every listed model has already been certified to every named standard. For a coating-preparation job, add the required workpiece cleanliness and profile to the process documents; these are verified on the blasted surface, not inferred from the shot-size code. The blasting media selection guide describes how to compare candidate media under controlled operating conditions.
Online models and non-selectable sizes
The product selectors show current online catalogue models. YUXIN's high-carbon shot technical description covers S70–S1110, while the online selector lists a narrower set; its published sieve table does not cover the entire stated range. The low-carbon shot description covers S110–S930, with a narrower online selector. If a size is mentioned in technical text but is absent from the selector, include it in a quotation request for supply and inspection confirmation. Do not infer current stock or a delivery date from a range statement.
Common size and standards questions
What does S330 mean in a steel shot order?
It is an SAE shot-size designation based on a nominal 0.0330 in (about 0.84 mm) test sieve. Specify the material and full distribution separately.
Can I replace GP25 with GH25 because both contain G25?
GP and GH are different hardness classes. Confirm the required class and size distribution, and recheck the process result before substituting.
Can I use a supplier's HRC value as an ISO 11125-3 hardness result?
Not without the test record. ISO 11125-3 specifies a Vickers method. Record the hardness scale, method, sample and acceptance requirement together.